Current Category : The Trax II - Go to Category Index | Search.

From this page you can securely order parts for the Trax II. You may cick here for comprehensive information on the Trax II or click here to go to the plans ordering page.

Instructions: Scroll down the list of parts and find the item or items that you want. For each part enter the quantity that you want and click on the "buy" button displayed for that item. You will then be taken to your current purchase list, and that item should have been added. If you need to order more click back button on your browser and and do the same for each item. However, if at this stage that is all you want to buy click on 'check out'. You will then be asked to fill out your information on a secure server.

All Prices are in Australian Dollars. ( USA residents will only pay approx 75% of list prices quoted due to exchange rates. ) Note: Our Australian dollar is only worth around 75 cents to the US dollar, that means USA residents will only pay around half the price shown here in Australian dollars.

Your Computer: If this page is not working as you think it should please make sure your internet browser has javascript enabled. Our javascript is harmless and enabling javascript can be done for just the time you are at our site if you wish. But generally it is enabled by default. If your not sure how to enbable it please try (in Internet Explorer) going to Tools > Options then the Security Tab where you can set it back to 'Default' or enabling 'Active Scripting'.

	FT01-DUP1		QTY:
	Chassis Frame, fully welded with holes drilled, mount brackets and axle beam welded on

	FLPN-01		QTY:
	Floor Pan, 2mm sheet, 830 x 550mm (can only be ordered if ordering FT01 Chassis)

	FT02		QTY:
	Chassis Frame Pack, pre-cut & drilled ready for welding (no front axle beam) (not needed if ordering FT01)

	FT03-DUP1		QTY:
	Front Axle Beam, fully welded with holes drilled

	TX-07		QTY:
	Front and rear Rollbar tubes unwelded, complete set prebent. Need to be trimmed to lenght (not required if ordering TX-02 or TX-03).

	TX-08		QTY:
	Fully welded Trax II Lower Chasis frame, Front and rear rollbars & side intrusion bars. All welded as one structure.

	FT04-DUP1		QTY:
	Steering Support, fully welded with holes drilled

	FT05-DUP1		QTY:
	Lower Steering Bracket, drilled

	FT06-DUP1		QTY:
	Top Steering Bracket, fully welded & drilled

	FT07-DUP1		QTY:
	4 Steering Bushes for top & lower Steering brackets (acetal)

	FT08		QTY:
	Steering Shaft, drilled with Steering Boss welded on

	SB01-DUP3		QTY:
	Steering Boss only. (not required if ordering Steering Shaft)

	FT09-DUP1		QTY:
	Bellcrank, welded & drilled. Comes with 6mm Rollpin

	FT10		QTY:
	Lock Collars, drilled & tapped with grub screw

	FT11		QTY:
	Tie Rods, welded with lock nuts

	BLIOD-DUP1		QTY:
	Tie Rod Ends, includes nyloc nuts

	FT12		QTY:
	Stub Axles, fully welded with uprights, steering arms, nuts, washers, & split pins

	BSH12-4		QTY:
	4 Stub Axle Bushes (acetal)

	STB12-2-DUP6		QTY:
	2 Stub Axle bolts, 12mm. Includes washers & nyloc nuts

	FT13-DUP1		QTY:
	Steering Kit, includes above parts: FT04, FT05, FT06, FT07, FT08, FT09, FT10, FT11, FT12, BLIOD, BSH12-4, STB12-2 (Discounted Price)

	FWH-01-DUP1		QTY:
	Front Wheel Hubs (steel) 5 stud H-T pattern. Includes studs, nuts, bearings, seals & dust caps

	STW-01-DUP2		QTY:
	Steering Wheel, 3-Spoke polymoulded 11" Æ (Black)

	FT14		QTY:
	Master Cylinder mount bracket, fully welded & drilled

	MSC-01		QTY:
	Master Cylinder 5/8" girling type

	FT15-DUP1		QTY:
	Master Cylinder Pushrod & Clevis Joint

	FT16		QTY:
	Brake Hose, stainless braided with banjo ends, 2 x banjo bolts & crush washers. 1760mm long

	FT17		QTY:
	Brake Kit: includes Master Cylinder, brake hose & caliper. Parts:MSC-01, FT16 & CAL-01

	FT18-DUP1		QTY:
	Brake Kit: includes Master Cylinder, brake hose & caliper. Parts:MSC-01, FT16 & CAL-01

	FT19-DUP1		QTY:
	Pedals, fully welded & drilled

	FT20		QTY:
	Throttle Cable, to suit 6.0 Vanguard motor

	FT21-DUP1		QTY:
	Rear Axle, 1000mm long, 1 ¼"Æ complete with keyways & wheel hubs fitted

	RWH-01-DUP1		QTY:
	Rear Wheel Hubs only, 1 ¼" bore 5 stud with studs & nuts (not needed if ordering Rear Axle)

	SPR-01-DUP2		QTY:
	Rear Drive Sprocket 82 tooth, 35-1, 3/8" pitch steel (suits mount hub: MHU-01)

	MHU-01-DUP1		QTY:
	Drive Hub for 82 tooth 3/8" Sprocket, keyed 1 ¼" bore, 4 holes on 4" PCD (2 required per vehicle)

	CH-351-100		QTY:
	35-1, 3/8" Pitch chain 100 links & connector link

	DBR-02-DUP4		QTY:
	Disc Rotor 240mm Æ , 5mm thick steel slotted, (suits mount hub: MHU-01)

See our Conditions of Sale.

[1] 2 Next Page

Secure ecommerce shopping cart software
and credit card processing provided by ezimerchant