Current Category : PIRCV Rear Suspension - Go to Category Index | Search.

Instructions: Scroll down the list of parts and find the item or items that you want. For each part enter the quantity that you want and click on the "buy" button displayed for that item. You will then be taken to your current purchase list, and that item should have been added. If you need to order more click back button on your browser and and do the same for each item. However, if at this stage that is all you want to buy click on 'check out'. You will then be asked to fill out your information on a secure server.

All Prices are in Australian Dollars. ( USA residents will only pay approx 75% of list prices quoted due to exchange rates. ) Note: Our Australian dollar is only worth around 75 cents to the US dollar, that means USA residents will only pay around half the price shown here in Australian dollars.

Your Computer: If this page is not working as you think it should please make sure your internet browser has javascript enabled. Our javascript is harmless and enabling javascript can be done for just the time you are at our site if you wish. But generally it is enabled by default. If your not sure how to enbable it please try (in Internet Explorer) going to Tools > Options then the Security Tab where you can set it back to 'Default' or enabling 'Active Scripting'.

	CV1		QTY:
	Laser cut plates for PIRCV centre housing, 22 plates, just needs welding.

	CV2		QTY:
	Bashplate, 5mm Aluminium with holes drilled.

	CV3		QTY:
	Central drive hub, fully machined, 4140 steel.

	DBRCV		QTY:
	Disc rotor, 4mm thick, laser cut with mount holes.

	CAL032		QTY:
	Brake caliper, twin piston with performance EBC Kevlar brake pads, includes bleed screw & banjo bolt.

	CV4		QTY:
	Caliper mount spacers & M8x30 bolts & washers

	SPR530-60CV		QTY:
	Drive sprocket, 60 tooth 530 pitch with countersunk mount holes

	CV5		QTY:
	Adjuster plates, (2) laser cut, tapped & countersunk.

	CV6		QTY:
	Bearing housings, machined 6061 T6 Aluminium.

	CIR115		QTY:
	Circlips 115mm Internal.

	60152RS-6		QTY:
	Bearings 115x75x20 set of 6.

	CVHUB-6		QTY:
	CV drive hubs, set of 6, machined 6061 T6 Aluminium.

	CPLUG-6		QTY:
	Brass 40mm core plugs, used for blanking off CV hubs

	CV7B		QTY:
	Bolt kit for centre drive, includes 6x M10x20 Buttonhead, 6x M10x16 CSK, 12x M8x20 CSK, 12x M8x55 Capscrews, 12x 8mm Flat washers, 6x M10x50 Capscrews.

	CV8		QTY:
	2 x Adjuster spacers, 1 x M10x120 bolt, washers & nyloc nut. (used for mounting hex adjuster mechanisum to plates).

	CVCART		QTY:
	Centre drive cartridge, complete centre drive assembly. As shown onPIRCV plans page 30.

	CV9		QTY:
	Centre drive spacers, machined from Aluminium.

	CV10		QTY:
	Centre drive load washers, machined from Aluminium.

	1/2ROD-2		QTY:
	1 x ½”UNF male RH rod end, 1 x ½” UNF male LH rod end. Comes with RH & LH ½” UNF Jam nuts, (locknuts).

	CV11		QTY:
	Hex adjuster, machined from 30mm Hex bar.LH & RH threads

	CV12		QTY:
	Adjuster spacers, (2) goes either side of rod end, includes 1x ½” UNF x 2 ½” Bolt with washers & nyloc nut.

	CV13		QTY:
	Top suspension arms, fully welded with adjuster nut housing, (2).

	CV13N		QTY:
	Top arm adjuster nuts, machined from 30mm Hex bar, (2).

	CV14		QTY:
	Lower suspension arms, fully welded with adjuster nut housings, (2).

	CV14N		QTY:
	Lower arm adjuster nuts, machined from 30mm hex bar, (4).

	BSH16-16		QTY:
	Suspension arm pivot bushes, Acetal, 16mm, (set of 16)

	5/8ROD-6		QTY:
	5/8” UNF male RH rod ends with 5/8” UNF Jam nuts, (6 of each).

	CV15B		QTY:
	Set of 8 pivot bolts, washers & nyloc nuts, M16x110mm long.

	CV16		QTY:
	Laser cut suspension upright housing plates, as per PIRCV plan page 48.

	CV17		QTY:
	Machined bearing housings only, for uprights (2)

	CV18		QTY:
	Machined upright bars only, for uprights, (2)

	CV19		QTY:
	Complete welded uprights with bearing housings, (2) (not required if ordering CV16, CV17, CV18.

	CV20		QTY:
	Laser cut 6 stud wheel plates, 8mm steel, countersunk holes with 12x 7/16” UNF wheel studs & 7/16” UNF wheel nuts.

	CV21B		QTY:
	Bolt kit for Uprights, includes 12x  M10x25 CSK, 12x M8x90 Capscrews, 12x 8mm Flat washers, 12x M8 Nyloc nuts, 4x 5/8” UNC x 2” Button head.

	CV22		QTY:
	Set of 4 upright spacers for rod end & shock mount (only required if making uprights to plans)

	CVASSEM		QTY:
	Driveshafts, pair, 930 Lobro type CV joints, splined axles & heavy duty rubber boots. 2 complete assemblies. Extended length = 580mm.

See our Conditions of Sale.

[1] 2 Next Page

Secure ecommerce shopping cart software
and credit card processing provided by ezimerchant