Email:
Password:  
General Buggy And Sandrail Components
 

General Buggy And Sandrail Components
NOTE: Prices show include 10% GST, which only applies to Australian customers. USA residents will only pay approx 107% of list prices quoted due to EXCHANGE rates. Click here to check the value in your local currency.

1/2" Chome moly rod end AUD$27.00
 
1 x 1/2" UNF Chrome moly left hand rod end with jam nut.
PART NUMBER:1/2ROD-LH-1
Qty:

1/2" Chrome moly rod end AUD$27.00
 
1 x 1/2" UNF Chrome moly right hand rod end with jam nut.
PART NUMBER:1/2ROD-RH-1
Qty:

3/4" Chrome moly Rod end AUD$40.00
 
1 x 3/4" UNF male right hand Chrome Moly Rod end, Includes 3/4" UNF Jam nut.
PART NUMBER:3/4ROD-RH-1
Qty:

5/8” UNF Male Rod Ends (4) AUD$120.00
 
4 x 5/8" Rod ends, 5/8” Chrome Moly UNF Male right hand with 5/8” UNF Jam nuts.
PART NUMBER:5/8ROD-4
Qty:

View Product Details 		5/8” UNF Male Rod Ends (6) AUD$180.00
 
6 x 5/8” UNF male Crome Moly right hand rod ends with 5/8” UNF Jam nuts.
PART NUMBER:5/8ROD-6
Qty:

Heavy Duty 930 CV joint boots AUD$118.00 (save $47.00)
 5 days left!
930 CV Over-boot, (set of 4) suits all 930 CV joints, These are the toughest 930 CV boots made. Designed by Edge & made of tough durable rubber. 4mm wall thickness & 5mm thickness at each end. 168mm overall length. Designed to fit a 25mm, (1”) axle & fit over the top of the CV joint. No mounting flanges required. (90-110mm hose clamp required to fit) (Will fit Edge manufactured PIRCV components from August 08’ onwards).
PART NUMBER:930BOOT x 4
Qty:

View Product Details 		930 Lobro CV Joint AUD$100.00
 
930CV, Spare CV joint, 930 Lobro type, includes outer, inner, cage & balls.
PART NUMBER:930CV
Qty:

View Product Details 		Bearing 115x75x20 AUD$25.00 (save $7.01)
 6 days left!
60152RS, Bearing 115x75x20, (1 only)
PART NUMBER:60152RS
Qty:

View Product Details 		Bearings 115x75x20 (6) AUD$145.00 (save $47.00)
 4 days left!
60152RS-6, Bearings 115x75x20 set of 6.
PART NUMBER:60152RS-6
Qty:

BAT260 AUD$160.00
 
Battery, 12 volt, 260 CCA, (cold cranking amps). 26 AH, (amp hours) AGM type, (Absorbed glass matt) fully sealed, requires no maintenance. Can be mounted at any angle. Dimensions: 175mm Long x 166mm wide x 125mm tall. Weight = 8 kg Amp-Tech brand.
PART NUMBER:BAT260
Qty:

View Product Details 		Barracuda Front Brake Kit AUD$875.00
 
Front brake kit, Suits 10" or 12" rims. includes BC10 welded uprights, FWH-04 hubs, CAL032x2 Calipers, DBR032 Rotors, HSE-06 Hoses, BB-03 Double banjo bolt, PEDBOX-2.
PART NUMBER:BCBRAKE
Qty:

Upgrade Front brake kit for Barracuda AUD$875.00
 
Barracuda Upgrade front brake kit to suit 12" rims. Larger 207mm rotors & larger twin piston calipers. Kit includes 2 x welded uprights, 2 x FWH-04 hubs, 2 x CALXVS Calipers, 2 x DBRXVS Rotors, HSE-06 Hoses, BB-03 Double banjo bolt, PEDBOX-2.
PART NUMBER:BCBRAKE XVS
Qty:

View Product Details 		Barracuda radiator AUD$420.00
 
Radiator, Brand new Aluminium three core, double bypass. 12” sucker Fan fitted to rear. 26mm Inlet & outlet fittings on lower tank to suit Hayabusa or most types of motorcycle engines. This is what Edge fit to their Barracuda buggies. 360mm wide x 460mm tall. Note: Edge can make a radiator to suit your buggy & change hose fitting sizes & location to suit your engine.
PART NUMBER:BCRAD
Qty:

View Product Details 		10mm Studded Rod End AUD$14.00
 
10mm studded rod end used on gear change linkage (
PART NUMBER:BL10D-1
Qty:

View Product Details 		Front Brake Kit AUD$635.00 (save $115.00)
 5 days left!
All the above parts to set up Front Brakes, including FWH-04 hubs, DBR032 rotors, CAL032 calipers, BB-01 banjo bolts, STUB032 stub axles, HSE-03 front brake hoses, BB-03 double banjo bolt, PEDBOX-2 brake pedal box, all nuts & bolts. For front left & right hand wheels. Suits Sidewinder & Piranha
PART NUMBER:BRAKE KIT
Qty:

Wheel nut for BTR rims AUD$6.00
 
Wheel nuts to suit 15" BTR rims. BTR rims have a VW style radius instead of a 60 degree taper for the wheel nut. Edge have custom made these nuts to suit the BTR rims. These nuts have the correct radius, 7/16" UNF thread to suit a standard wheel stud, 7/8" Hex, 35mm long with a domed head. (sold individually).
PART NUMBER:BTR-NUT
Qty:

Hayabusa Exhaust header flanges AUD$40.00
 
Hayabusa Exhaust header flanges, set of 4, 6mm Stainless steel, 39mm centre hole, used when making your own pipes.
PART NUMBER:BUSA EX-4
Qty:

Hayabusa exhaust header pipe stubs. AUD$42.00
 
Set of 4 machined exhaust header stubs to suit Hayabusa engine, all models. 38.3mm bore to suit 1 1/2", (38.1mm) exhaust tube. 45.3mm OD x 19mm thick. 1mm Chamfer on one inside edge for welding in exhaust tube. These stubs fit on the very end of the exhaust system where the header pipes bolt up into the cylinder head & they sit against the exhaust port sealing gasket rings. (used for making your own exhaust system).
PART NUMBER:BUSA EX-STUB
Qty:

Hayabusa engine mount slugs AUD$35.00
 
Engine mount slugs to mount a Suzuki Hayabusa engine. 4 x 10mm & 4 x 12mm, all 25.4mm diameter & 40mm long. Made from 1020 Steel. These slugs bolt to the engine mount holes to give you an area to weld mounting tubes or plates to. Set of 8. May suit other engines with 10mm & 12mm mount holes.
PART NUMBER:BUSA-MNT
Qty:

View Product Details 		Brake Caliper (Twin Piston) (Pair) AUD$270.00
 
Brake Calipers, matching pair alloy twin piston calipers, right & left sides, for front brakes
PART NUMBER:CAL032x2
Qty:

Chain join link 530 AUD$11.00 (save $4.00)
 3 days left!
Spare Connector link for Edge CH530-114 530 O-Ring chain.
PART NUMBER:CH530 CON
Qty:

View Product Details 		115mm Circlips AUD$16.01
 
Circlips 115mm Internal fit.
PART NUMBER:CIR115
Qty:

View Product Details 		CV-SHAFT AUD$125.00
 
Spare driveshaft for PIRCV rear end/Barracuda rear suspension. Suits 930 CV joints, 579mm long, (22.8").
PART NUMBER:CV-SHAFT
Qty:

View Product Details 		Front Disc Rotors AUD$80.00
 
Front Disc Rotors, 180mm dia, 4mm steel slotted, suits FWH-04 Front Wheel Disc Hubs only. Suits Sidewinder, Piranha & Barracuda.
PART NUMBER:DBR032
Qty:

View Product Details 		Double Roller Chain Tensioner AUD$98.01
 
Chain Tensioner, Double Roller. Self compensates chain snatch
PART NUMBER:EP15
Qty:

View Product Details 		Fuel Filter AUD$6.01
 
Fuel Filter, Inline plastic filter
PART NUMBER:F-FILTER
Qty:

View Product Details 		Front Wheel Hubs (4 Stud Mini Pattern) AUD$65.01
 
Front wheel hubs (steel) 4 stud mini pattern with studs, nuts, bearings, seals & dust caps
PART NUMBER:FWH-03
Qty:

View Product Details 		Front Wheel Hubs (with Disc Rotor Mount) AUD$165.00
 
Front Wheel hubs with disc rotor mount, alloy, 4 Stud 156mm PCD, 7/16" UNF Studs, nuts, taper roller bearings & seals.
PART NUMBER:FWH-04
Qty:

View Product Details 		Front Wheel Bearings AUD$50.00
 
Suits all Edge buggies, (except Raven) Front wheel
PART NUMBER:FWH-BEAR
Qty:

Gimec reverse AUD$632.50
 
Gimec reverse FNR Forward neutral reverse box, made in Italy. Rated to 22 hp, suitable for industrial engines. 3/4" input shaft with keyway. Two splined output shafts for axles. Comes with splined adaptor sleeves that you can weld output flanges or axle shfts to.
PART NUMBER:Gimec reverse
Qty:

M8CLEVIS AUD$8.00
 
M8 clevis. With quick disconnect pin. M8x1.25 female thread. Used for brake master cylinders or gear shift linkages.
PART NUMBER:M8CLEVIS
Qty:

View Product Details 		Master Cylinder (5/8") AUD$56.00
 
Master Cylinder 5/8" girling type
PART NUMBER:MSC-01
Qty:

View Product Details 		Pedal AUD$25.00
 
Pedal, laser cut racing desgin with Acetal pivot bushes. Fits Pedal Box
PART NUMBER:PEDAL
Qty:

CV joint adaptor kit for Piranha AUD$640.00
 
Adaptor kit to fit Porsche 924 axles & CV joints to the Piranha. Includes the following parts: 1x Splined Centre shaft, 2 x Splined axles with billet wheel hubs, (4 stud 115mm PCD) 4 x CV splined adaptor hubs, 4 x retaining bolts & washers. To suit type 2 CV joints of 6 x M8 bolts on 86mm PCD. This kit suits Single or Double A arm rear suspensions & replaces parts PIR06 & IND-08. Part PIR12, (driveshafts) are replaced by purchasing original Porsche 924 CV joint/axle assemblies. Instead of
PART NUMBER:PIR924-KIT
Qty:

View Product Details 		Rack and Pinion AUD$419.99
 
Performance XRV Rack & Pinion, with adjustable gear mesh. Comes with 4 x M8x40 capscrews & nuts.To suit Barracuda.
PART NUMBER:RACK
Qty:

View Product Details 		Steering Rack Boot AUD$14.00
 
Universal steering rack boot (Use to replace old boots on Mini or Escort rack & pinion)
PART NUMBER:RACKBOOT
Qty:

Rack & Pinion gear set AUD$185.00
 
Spare rack & pinion gearset to suit Edge rack & pinion, made from heat treated & ground 4140 steel.
PART NUMBER:RACKGEAR
Qty:

Racing fuel filler cap AUD$64.00
 
RCI racing fuel filler cap, flush mount, includes mounting load ring, ( mounting load ring has studs fitted & hooks up from inside the tank, nuts go on from the outside). Outer flange diameter 151mm. 12 x 1/4" UNF mount studs on 135mm PCD. Inside opening is 76mm.
PART NUMBER:RCI CAP
Qty:

View Product Details 		Rollbars AUD$215.00
 
Rollbars, front & rear, (not required if ordering chassis)
PART NUMBER:ROLL2
Qty:

Set of 4 mount rubbers AUD$6.00
 
Set of 4 mounting rubbers, used as issolation mounts for fuel tanks, radiators, seats & other items, 30mm outside diameter x 15mm thick, 10mm hole. (set of 4)
PART NUMBER:RUBBERS
Qty:

Rear Wheel hubs blank AUD$115.00
 
Wheel hub, Blank no holes, 1 1/4", (31.75mm) bore, 137mm outside diameter, 63mm location diameter, 8mm thick flange. Machined from 1045 Billet steel. No stud pattern drilled so you can drill to your own wheel pattern. Pair, (2).
PART NUMBER:RWH-BLANK
Qty:

Steering wheel flange AUD$16.00
 
Steering wheel flange, has outer bolt pattern of 6 x 5.5mm holes on 70mm PCD as well as inner three hole Go Kart bolt pattern. Can either be welded to steering column as per normal instalation or used as an adaptor plate from three hole to six hole when fitting a larger steering wheel.
PART NUMBER:SB05
Qty:

View Product Details 		FRONT SHOCKS, (Pair) KIT AUD$655.00
 
Front shocks, coilovers, gas filled, heavy duty, 14mm 500 lb coil springs, rebuildable, adjustable preload, 390mm eye to eye. (2)
PART NUMBER:SHOCK 390
Qty:

View Product Details 		Rear Shock (1) KIT AUD$345.00
 
Rear Shock, gas filled heavy duty with 12mm coil springs, Adjustable spring preload, rebuildable, 465mm eye to eye
PART NUMBER:SHOCK465
Qty:

View Product Details 		REAR SHOCKS, (Pair) KIT AUD$765.00
 
Rear shocks, coilover, gas filled, heavy duty, 12mm coils, rebuildable, 750mm eye to eye. (2) Suits Piranha series II.
PART NUMBER:SHOCK 750R
Qty:

Shocks 790mm, (Pair) KIT AUD$790.00
 
Shocks, coilover, gas filled heavy duty, 12mm coils, 790mm eye to eye, (2 shocks) suit front or rear of Barracuda, (2 pairs required for buggy).
PART NUMBER:SHOCK790
Qty:

View Product Details 		Shock adjuster collar AUD$38.00
 
Shock threaded adjuster collar, Aluminium, fits all Edge shocks, M60x2 thread, used for pre-loading spring.
PART NUMBER:SHOCKADJ
Qty:

View Product Details 		Shock adjuster lock ring AUD$36.00
 
Shock threaded adjuster lock collar, Aluminium, fits all Edge shocks, M60x2 thread, used for locking adjuster collar.
PART NUMBER:SHOCKLOK
Qty:

SLUG-10mm AUD$5.00
 
Slug with 10mm drilled hole, 1", (25.4mm) OD. 40mm long. Used for motorcycle engine mounts that have 10mm mount holes.
PART NUMBER:SLUG-10mm
Qty:

SLUG-12mm AUD$5.00
 
Slug with 12mm drilled hole, 1", (25.4mm) OD. 40mm long. Used for motorcycle engine mounts that have 12mm mount holes. Also used as shock mounts when making Sidewinder & Piranha front suspension arms, (4 required for front arm application) Not required if purchasing Edge SW07 front suspension arms.
PART NUMBER:SLUG-12mm
Qty:

SLUG-16mm AUD$5.00
 
Slug with 16mm drilled hole, 1", (25.4mm) OD. 40mm long. Used for motorcycle engine mounts that have 16mm mount holes. Also used to make Raven, Fun Kart II & Trax II & Belcranks & lock collars, as well as the Raven brake bar. (Not required if buying these parts pre-fabricated from The Edge).
PART NUMBER:SLUG-16mm
Qty:

View Product Details 		Stub Axles plain machined. AUD$48.00
 
Machined pair of plain stub axles, comes with castle nuts, washers & split pins, (not required if ordering STUB032)
PART NUMBER:STUB-01
Qty:

View Product Details 		Front Stub Axles (w/ Caliper mounts) AUD$105.00
 
Front Stub axles, left & right, welded & drilled with uprights & steering arms, calliper mounts (2). Suit calipers CAL032x2 & wheel hubs FWH-04. Suits Sidewinder & Piranha.
PART NUMBER:STUB032
Qty:

View Product Details 		Fuel Tap AUD$18.01
 
Fuel tap, heavy duty ball valve, chrome plated brass with ¼” BSP female threads each end.
PART NUMBER:TAP-01
Qty:

View Product Details 		Tie Down Straps AUD$30.01
 
Motorcycle type Tie Down Straps. We use them for fixing down fuel tanks & for holding your vehicle on the trailer
PART NUMBER:TIEDOWN
Qty:

View Product Details 		Rack and Pinion, KIT AUD$460.01
 
Rack and Pinion. 1/2 turn lock, with adjustable gear mesh. Includes tie rods to suit Sidewinder and Piranha as well as input shaft adaptor
PART NUMBER:XRV RACK
Qty:

XRVHOUS-2 AUD$225.00
 
XRV627 rear bolt in housing Old stock, fully welded, powdercoated, never used. This one contains a sprocket & drive hub as well as output bearings & flanges. This was a bolt in rear end that runs a 50 tooth sprocket enclosed within the case. A 20 or 22hp Briggs & Stratton Vangaurd vee twin bolts on the top. In the top rear mounts a 1” diameter layshaft on two UC205 1” bearings & PF205 housings. The layshaft has a sprocket that sits within the case to drive the main sprocket.
PART NUMBER:XRVHOUS-2
Qty:

XRVHOUS-3 AUD$200.00
 
XRV627 rear bolt in housing Old stock, fully welded, powdercoated, never used. This was a bolt in rear end that runs a 50 tooth sprocket enclosed within the case. A 20 or 22hp Briggs & Stratton Vangaurd vee twin bolts on the top. In the top rear mounts a 1” diameter layshaft on two UC205 1” bearings & PF205 housings. The layshaft has a sprocket that sits within the case to drive the main sprocket. In the top of the housing is provision for a chain tensioner.
PART NUMBER:XRVHOUS-3
Qty:

XRVHOUS-4 AUD$125.00
 
XRV627 rear bolt in housing 3rd prototype. Old stock, fully welded, never used. This was a bolt in rear end that runs a 50 tooth sprocket enclosed within the case. A 20 or 22hp Briggs & Stratton Vangaurd vee twin bolts on the top. In the top rear mounts a 1” diameter layshaft on two UC205 1” bearings & PF205 housings. The layshaft has a sprocket that sits within the case to drive the main sprocket. In the top of the housing is provision for a chain tensioner.
PART NUMBER:XRVHOUS-4
Qty: