Email:
Password:  
Barracuda spare parts
 

Replacement/repair parts for your Barracuda.
NOTE: Prices show include 10% GST, which only applies to Australian customers. USA residents will only pay approx 107% of list prices quoted due to EXCHANGE rates. Click here to check the value in your local currency.

1/2" Chome moly rod end AUD$27.00
 
1 x 1/2" UNF Chrome moly left hand rod end with jam nut.
PART NUMBER:1/2ROD-LH-1
Qty:

1/2" Chrome moly rod end AUD$27.00
 
1 x 1/2" UNF Chrome moly right hand rod end with jam nut.
PART NUMBER:1/2ROD-RH-1
Qty:

3/4" Chrome moly Rod end AUD$40.00
 
1 x 3/4" UNF male right hand Chrome Moly Rod end, Includes 3/4" UNF Jam nut.
PART NUMBER:3/4ROD-RH-1
Qty:

View Product Details 		5/8” UNF male RH Rod End AUD$30.00
 
1 x 5/8” UNF male Chrome Moly right hand rod end with 5/8” UNF Jam nut.
PART NUMBER:5/8 ROD-1
Qty:

5/8” UNF Male Rod Ends (4) AUD$120.00
 
4 x 5/8" Rod ends, 5/8” Chrome Moly UNF Male right hand with 5/8” UNF Jam nuts.
PART NUMBER:5/8ROD-4
Qty:

View Product Details 		5/8” UNF Male Rod Ends (6) AUD$180.00
 
6 x 5/8” UNF male Crome Moly right hand rod ends with 5/8” UNF Jam nuts.
PART NUMBER:5/8ROD-6
Qty:

View Product Details 		Brake Pad AUD$32.00
 
032 PAD, Spare brake pads to suit The Edge Products CAL032 rear caliper.
PART NUMBER:032 PAD
Qty:

View Product Details 		Replacement Rubber Overboot (930CV Joint) AUD$48.00
 
1 x Replacement rubber overboot for 930 CV joint.
PART NUMBER:930BOOT
Qty:

View Product Details 		930 Lobro CV Joint AUD$100.00
 
930CV, Spare CV joint, 930 Lobro type, includes outer, inner, cage & balls.
PART NUMBER:930CV
Qty:

View Product Details 		Bearing 115x75x20 AUD$25.00 (save $7.01)
 9 days left!
60152RS, Bearing 115x75x20, (1 only)
PART NUMBER:60152RS
Qty:

View Product Details 		Accelerator Pedal Spring AUD$4.00
 
Accelerator pedal spring, used on all Edge buggies.
PART NUMBER:ACCEL SPRING
Qty:

View Product Details 		Double Banjo Bolt AUD$9.00
 
Double Banjo bolt, M10x1.25, adapts two front brake hoses to master cylinder. Comes with three crush washers.
PART NUMBER:BB-03
Qty:

BC TRACK ROD AUD$375.00
 
Complete track rod kit with weld on chassis mounts, rod ends & adjusters. This kit is designed to go between the chassis side & the rear suspension uprights to give more torsional support to the rear suspension. One end of the track rod has a weld-on mount that welds to the chassis. The other end is a clevis which replaces the bolt through the top suspension arm mount point. The track rods have chrome moly rod ends at each end with a right & left hand adjuster to tune.
PART NUMBER:BC TRACK ROD
Qty:

View Product Details 		Suspension Arm Pivot Bushes (16) AUD$112.00
 
Suspension arm pivot bushes, Acetal, 16mm, (set of 16).
PART NUMBER:BSH16-16
Qty:

View Product Details 		Supension Arm Pivot Bushes (8) AUD$56.01
 
Suspension Arm Pivot Bushes, Acetal (set of 8)
PART NUMBER:BSH16-8
Qty:

Wheel nut for BTR rims AUD$6.00
 
Wheel nuts to suit 15" BTR rims. BTR rims have a VW style radius instead of a 60 degree taper for the wheel nut. Edge have custom made these nuts to suit the BTR rims. These nuts have the correct radius, 7/16" UNF thread to suit a standard wheel stud, 7/8" Hex, 35mm long with a domed head. (sold individually).
PART NUMBER:BTR-NUT
Qty:

Hayabusa Exhaust header flanges AUD$40.00
 
Hayabusa Exhaust header flanges, set of 4, 6mm Stainless steel, 39mm centre hole, used when making your own pipes.
PART NUMBER:BUSA EX-4
Qty:

Hayabusa exhaust header pipe stubs. AUD$42.00
 
Set of 4 machined exhaust header stubs to suit Hayabusa engine, all models. 38.3mm bore to suit 1 1/2", (38.1mm) exhaust tube. 45.3mm OD x 19mm thick. 1mm Chamfer on one inside edge for welding in exhaust tube. These stubs fit on the very end of the exhaust system where the header pipes bolt up into the cylinder head & they sit against the exhaust port sealing gasket rings. (used for making your own exhaust system).
PART NUMBER:BUSA EX-STUB
Qty:

View Product Details 		Busa straight thermostat housing AUD$137.50
 
Thermo housing for Suzuki Hayabusa, all years.replaces standard angled item.
PART NUMBER:BUSA THERMO
Qty:

Large XVS caliper, Left side AUD$155.00
 
Large XVS brake caliper, Left side. Used on upgraded front brakes. twin piston
PART NUMBER:CALXVS-LH
Qty:

Large XVS caliper, Right side AUD$155.00
 
Large XVS brake caliper, right side. Used on upgraded front brakes. twin piston.
PART NUMBER:CALXVS-RH
Qty:

Large upgrade calipers, Right & Left AUD$310.00
 
Large XVS brake calipers, Left & Right side. Used on upgraded front brakes. twin piston, Pair, (2)
PART NUMBER:CALXVSx2
Qty:

Chain join link 530 AUD$11.00 (save $4.00)
 6 days left!
Spare Connector link for Edge CH530-114 530 O-Ring chain.
PART NUMBER:CH530 CON
Qty:

View Product Details 		CV Drive Hub AUD$92.00
 
CV drive hub, (1 only), machined 6061 T6 Aluminium.
PART NUMBER:CVHUB
Qty:

View Product Details 		CV-SHAFT AUD$125.00
 
Spare driveshaft for PIRCV rear end/Barracuda rear suspension. Suits 930 CV joints, 579mm long, (22.8").
PART NUMBER:CV-SHAFT
Qty:

Floating Rotor 280mm AUD$135.00
 
Floating disc rotor, 280mm diameter, 5mm thick, to suit standard PIRCV rear end & CAL032 caliper/CV5 Adjuster plates, upgrade from part DBRCV.
PART NUMBER:DBR280CV
Qty:

Floating disc rotor 312mm AUD$145.00
 
Floating disc rotor, 312mm diameter 5mm thick, 6 bolt mount to suit upgraded PIRCV rear end.
PART NUMBER:DBR312R
Qty:

EXHAUST MUFFLER FLANGE AUD$15.00
 
Exhaust flange to suit muffler mount. Welds on the end of exhaust system, 3 hole pattern matches Hayabusa muffler, 2 1/2" hole, 6mm thick plate.
PART NUMBER:EX-FLANGE
Qty:

Spare brake pads AUD$48.00
 
Spare brake pads to suit the PIRCV brake caliper,(suits XVS calipers) EBC brand organic carbon graphite/sintered (fits upgraded large caliper only).
PART NUMBER:FA199PAD
Qty:

View Product Details 		Fuel Filter AUD$6.01
 
Fuel Filter, Inline plastic filter
PART NUMBER:F-FILTER
Qty:

View Product Details 		Front Wheel Bearings AUD$50.00
 
Suits all Edge buggies, (except Raven) Front wheel
PART NUMBER:FWH-BEAR
Qty:

M8CLEVIS AUD$8.00
 
M8 clevis. With quick disconnect pin. M8x1.25 female thread. Used for brake master cylinders or gear shift linkages.
PART NUMBER:M8CLEVIS
Qty:

View Product Details 		Master Cylinder (5/8") AUD$56.00
 
Master Cylinder 5/8" girling type
PART NUMBER:MSC-01
Qty:

View Product Details 		Sports Bike Muffler AUD$380.00
 
Stainless steel sports bike muffler, Hayabusa 3 hole mount flange.
PART NUMBER:MUFFLER-SS
Qty:

View Product Details 		Pedal AUD$25.00
 
Pedal, laser cut racing desgin with Acetal pivot bushes. Fits Pedal Box
PART NUMBER:PEDAL
Qty:

View Product Details 		Replacement housing for Edge rack and pinion AUD$178.00
 
Replacement housing for Edge rack & pinion. Made from Billet 6061 T6 Aluminium.
PART NUMBER:RACKBODY
Qty:

Rack & Pinion gear set AUD$185.00
 
Spare rack & pinion gearset to suit Edge rack & pinion, made from heat treated & ground 4140 steel.
PART NUMBER:RACKGEAR
Qty:

Racing fuel filler cap AUD$64.00
 
RCI racing fuel filler cap, flush mount, includes mounting load ring, ( mounting load ring has studs fitted & hooks up from inside the tank, nuts go on from the outside). Outer flange diameter 151mm. 12 x 1/4" UNF mount studs on 135mm PCD. Inside opening is 76mm.
PART NUMBER:RCI CAP
Qty:

Set of 4 mount rubbers AUD$6.00
 
Set of 4 mounting rubbers, used as issolation mounts for fuel tanks, radiators, seats & other items, 30mm outside diameter x 15mm thick, 10mm hole. (set of 4)
PART NUMBER:RUBBERS
Qty:

View Product Details 		Shock adjuster collar AUD$38.00
 
Shock threaded adjuster collar, Aluminium, fits all Edge shocks, M60x2 thread, used for pre-loading spring.
PART NUMBER:SHOCKADJ
Qty:

View Product Details 		Shock adjuster lock ring AUD$36.00
 
Shock threaded adjuster lock collar, Aluminium, fits all Edge shocks, M60x2 thread, used for locking adjuster collar.
PART NUMBER:SHOCKLOK
Qty:

Sprocket kit AUD$165.00
 
Upgraded rear drive sprocket for PIRCV rear end, includes 8mm thick, steel 60 tooth 530 pitch sprocket, drive flange that fits over CV3 drive hub, 12 x M10 mounting screws, 6 x M10 Nyloc nuts, 6 x 4mm Rollpins. The flange bolts to the inside of the sprocket & uses the CV3 drive hub as a spline drive. The rollpins stop the original 6 drive screws un-winding. (all Edge CVCARTS have this kit as standard).
PART NUMBER:SPR530-60KIT
Qty:

View Product Details 		13 Tooth Sprocket (99-07 Hayabusa Engine) AUD$42.00
 
13 Tooth Sprocket (99-07 Hayabusa Engine)
PART NUMBER:SPRBUSA13
Qty:

View Product Details 		14 Tooth Sprocket (99-07 Hayabusa Engine) AUD$42.00
 
13 Tooth Sprocket (99-07 Hayabusa)
PART NUMBER:SPRBUSA14
Qty:

View Product Details 		15 Tooth Sprocket (99-07 Hayabusa Engine) AUD$42.00
 
15 Tooth Sprocket (99-07 Hayabusa Engine)
PART NUMBER:SPRBUSA15
Qty:

View Product Details 		13.5" Steering Wheel AUD$125.00
 
Steering wheel, 13.5” 3 spoke, contoured thumb grips, suits SB04 or SB05 Flange.
PART NUMBER:STW-02
Qty:

View Product Details 		Wheel Nut AUD$1.50
 
Spare 7/16” UNF wheelnuts
PART NUMBER:WHEELNUT
Qty:

View Product Details 		Wheel Stud AUD$2.00
 
Spare 7/16”UNF knurled head wheel studs
PART NUMBER:WHEELSTUD
Qty: