Edge Products - General Buggy And Sandrail Components

General Buggy And Sandrail Components

NOTE: Prices show include 10% GST, which only applies to Australian customers. USA residents will only pay approx 107% of list prices quoted due to EXCHANGE rates. Click here to check the value in your local currency.

1/2" Chome moly rod end

AUD$22.00 (save $5.00)

13 days left!

1 x 1/2" UNF Chrome moly left hand rod end with jam nut.

PART NUMBER:1/2ROD-LH-1

Qty:

1/2" Chrome moly rod end

AUD$22.00 (save $5.00)

13 days left!

1 x 1/2" UNF Chrome moly right hand rod end with jam nut.

PART NUMBER:1/2ROD-RH-1

Qty:

3/4" Chrome moly Rod end

AUD$32.00 (save $8.00)

13 days left!

1 x 3/4" UNF male right hand Chrome Moly Rod end, Includes 3/4" UNF Jam nut.

PART NUMBER:3/4ROD-RH-1

Qty:

5/8” UNF Male Rod Ends (4)

AUD$88.00 (save $32.00)

13 days left!

4 x 5/8" Rod ends, 5/8” Chrome Moly UNF Male right hand with 5/8” UNF Jam nuts.

PART NUMBER:5/8ROD-4

Qty:

View Product Details

5/8” UNF Male Rod Ends (6)

AUD$132.00 (save $48.00)

13 days left!

6 x 5/8” UNF male Crome Moly right hand rod ends with 5/8” UNF Jam nuts.

PART NUMBER:5/8ROD-6

Qty:

Heavy Duty 930 CV joint boots

AUD$165.00

930 CV Over-boot, (set of 4) suits all 930 CV joints, These are the toughest 930 CV boots made. Designed by Edge & made of tough durable rubber. 4mm wall thickness & 5mm thickness at each end. 168mm overall length. Designed to fit a 25mm, (1”) axle & fit over the top of the CV joint. No mounting flanges required. (90-110mm hose clamp required to fit) (Will fit Edge manufactured PIRCV components from August 08’ onwards).

PART NUMBER:930BOOT x 4

Qty:

View Product Details

930 Lobro CV Joint

AUD$100.00

930CV, Spare CV joint, 930 Lobro type, includes outer, inner, cage & balls.

PART NUMBER:930CV

Qty:

View Product Details

Bearing 115x75x20

AUD$32.01

60152RS, Bearing 115x75x20, (1 only)

PART NUMBER:60152RS

Qty:

View Product Details

Bearings 115x75x20 (6)

AUD$192.01

60152RS-6, Bearings 115x75x20 set of 6.

PART NUMBER:60152RS-6

Qty:

View Product Details

Barracuda Front Brake Kit

AUD$750.00 (save $124.99)

13 days left!

Front brake kit, Suits 10" or 12" rims. includes BC10 welded uprights, FWH-04 hubs, CAL032x2 Calipers, DBR032 Rotors, HSE-06 Hoses, BB-03 Double banjo bolt, PEDBOX-2.

PART NUMBER:BCBRAKE

Qty:

Upgrade Front brake kit for Barracuda

AUD$775.00 (save $100.00)

13 days left!

Barracuda Upgrade front brake kit to suit 12" rims. Larger 207mm rotors & larger twin piston calipers. Kit includes 2 x welded uprights, 2 x FWH-04 hubs, 2 x CALXVS Calipers, 2 x DBRXVS Rotors, HSE-06 Hoses, BB-03 Double banjo bolt, PEDBOX-2.

PART NUMBER:BCBRAKE XVS

Qty:

Barracuda radiator

AUD$385.00 (save $35.00)

13 days left!

Radiator, Brand new Aluminium twin core, double bypass. 12” sucker Fan fitted to rear. 26mm Inlet & outlet fittings on lower tank to suit Hayabusa or most types of motorcycle engines. This is what Edge fit to their Barracuda buggies. 360mm wide x 460mm tall. Note: Edge can make a radiator to suit your buggy & change hose fitting sizes & location to suit your engine.

PART NUMBER:BCRAD

Qty:

View Product Details

10mm Studded Rod End

AUD$14.00

10mm studded rod end used on gear change linkage (

PART NUMBER:BL10D-1

Qty:

View Product Details

Front Brake Kit

AUD$650.00 (save $100.00)

13 days left!

All the above parts to set up Front Brakes, including FWH-04 hubs, DBR032 rotors, CAL032 calipers, BB-01 banjo bolts, STUB032 stub axles, HSE-03 front brake hoses, BB-03 double banjo bolt, PEDBOX-2 brake pedal box, all nuts & bolts. For front left & right hand wheels. Suits Sidewinder & Piranha

PART NUMBER:BRAKE KIT

Qty:

Wheel nut for BTR rims

AUD$6.00

Wheel nuts to suit 15" BTR rims. BTR rims have a VW style radius instead of a 60 degree taper for the wheel nut. Edge have custom made these nuts to suit the BTR rims. These nuts have the correct radius, 7/16" UNF thread to suit a standard wheel stud, 7/8" Hex, 35mm long with a domed head. (sold individually).

PART NUMBER:BTR-NUT

Qty:

Hayabusa Exhaust header flanges

AUD$40.00

Hayabusa Exhaust header flanges, set of 4, 6mm Stainless steel, 39mm centre hole, used when making your own pipes.

PART NUMBER:BUSA EX-4

Qty:

Hayabusa exhaust header pipe stubs.

AUD$32.00 (save $10.00)

13 days left!

Set of 4 machined exhaust header stubs to suit Hayabusa engine, all models. 38.3mm bore to suit 1 1/2", (38.1mm) exhaust tube. 45.3mm OD x 19mm thick. 1mm Chamfer on one inside edge for welding in exhaust tube. These stubs fit on the very end of the exhaust system where the header pipes bolt up into the cylinder head & they sit against the exhaust port sealing gasket rings. (used for making your own exhaust system).

PART NUMBER:BUSA EX-STUB

Qty:

Hayabusa engine mount slugs

AUD$35.00

Engine mount slugs to mount a Suzuki Hayabusa engine. 4 x 10mm & 4 x 12mm, all 25.4mm diameter & 40mm long. Made from 1020 Steel. These slugs bolt to the engine mount holes to give you an area to weld mounting tubes or plates to. Set of 8. May suit other engines with 10mm & 12mm mount holes.

PART NUMBER:BUSA-MNT

Qty:

View Product Details

Brake Caliper (Twin Piston) (Pair)

AUD$170.00 (save $99.99)

13 days left!

Brake Calipers, matching pair alloy twin piston calipers, right & left sides, for front brakes

PART NUMBER:CAL032x2

Qty:

Chain join link 530

AUD$8.00

Spare Connector link for Edge CH530-114 530 O-Ring chain.

PART NUMBER:CH530 CON

Qty:

View Product Details

115mm Circlips

AUD$16.01

Circlips 115mm Internal fit.

PART NUMBER:CIR115

Qty:

View Product Details

Front Disc Rotors

AUD$80.00

Front Disc Rotors, 180mm dia, 4mm steel slotted, suits FWH-04 Front Wheel Disc Hubs only. Suits Sidewinder, Piranha & Barracuda.

PART NUMBER:DBR032

Qty:

View Product Details

Fuel Filter

AUD$6.01

Fuel Filter, Inline plastic filter

PART NUMBER:F-FILTER

Qty:

View Product Details

Front Wheel Hubs (4 Stud Mini Pattern)

AUD$65.01

Front wheel hubs (steel) 4 stud mini pattern with studs, nuts, bearings, seals & dust caps

PART NUMBER:FWH-03

Qty:

View Product Details

Front Wheel Hubs (with Disc Rotor Mount)

AUD$165.00

Front Wheel hubs with disc rotor mount, alloy, 4 Stud 156mm PCD, 7/16" UNF Studs, nuts, taper roller bearings & seals.

PART NUMBER:FWH-04

Qty:

View Product Details

Front Wheel Bearings

AUD$50.00

Suits all Edge buggies, (except Raven) Front wheel

PART NUMBER:FWH-BEAR

Qty:

Drive Hub (BLANK)

AUD$59.00 (save $9.00)

13 days left!

Drive hub used for disc rotor or sprocket, bored 1 1/4", (31.75mm) 10mm keyway, 120mm outside diameter, 8mm thick flange, 86mm location diameter for disc or sprocket, machined from 1045 billet steel. No hole pattern drilled so you can drill your own to suit your disc or sprocket.

PART NUMBER:MHU-BLANK

Qty:

View Product Details

Master Cylinder (5/8")

AUD$44.00 (save $8.00)

13 days left!

Master Cylinder 5/8" girling type

PART NUMBER:MSC-01

Qty:

View Product Details

Pedal

AUD$25.00

Pedal, laser cut racing desgin with Acetal pivot bushes. Fits Pedal Box

PART NUMBER:PEDAL

Qty:

CV joint adaptor kit for Piranha

AUD$640.00

Adaptor kit to fit Porsche 924 axles & CV joints to the Piranha. Includes the following parts: 1x Splined Centre shaft, 2 x Splined axles with billet wheel hubs, (4 stud 115mm PCD) 4 x CV splined adaptor hubs, 4 x retaining bolts & washers. To suit type 2 CV joints of 6 x M8 bolts on 86mm PCD. This kit suits Single or Double A arm rear suspensions & replaces parts PIR06 & IND-08. Part PIR12, (driveshafts) are replaced by purchasing original Porsche 924 CV joint/axle assemblies. Instead of

PART NUMBER:PIR924-KIT

Qty:

View Product Details

Rack and Pinion

AUD$419.99

Performance XRV Rack & Pinion, with adjustable gear mesh. Comes with 4 x M8x40 capscrews & nuts.To suit Barracuda.

PART NUMBER:RACK

Qty:

View Product Details

Steering Rack Boot

AUD$14.00

Universal steering rack boot (Use to replace old boots on Mini or Escort rack & pinion)

PART NUMBER:RACKBOOT

Qty:

Rack & Pinion gear set

AUD$185.00

Spare rack & pinion gearset to suit Edge rack & pinion, made from heat treated & ground 4140 steel.

PART NUMBER:RACKGEAR

Qty:

Racing fuel filler cap

AUD$64.00

RCI racing fuel filler cap, flush mount, includes mounting load ring, ( mounting load ring has studs fitted & hooks up from inside the tank, nuts go on from the outside). Outer flange diameter 151mm. 12 x 1/4" UNF mount studs on 135mm PCD. Inside opening is 76mm.

PART NUMBER:RCI CAP

Qty:

View Product Details

Rollbars

AUD$215.00

Rollbars, front & rear, (not required if ordering chassis)

PART NUMBER:ROLL2

Qty:

Set of 4 mount rubbers

AUD$6.00

Set of 4 mounting rubbers, used as issolation mounts for fuel tanks, radiators, seats & other items, 30mm outside diameter x 15mm thick, 10mm hole. (set of 4)

PART NUMBER:RUBBERS

Qty:

Rear Wheel hubs blank

AUD$96.00 (save $19.00)

13 days left!

Wheel hub, Blank no holes, 1 1/4", (31.75mm) bore, 137mm outside diameter, 63mm location diameter, 8mm thick flange. Machined from 1045 Billet steel. No stud pattern drilled so you can drill to your own wheel pattern. Pair, (2).

PART NUMBER:RWH-BLANK

Qty:

Steering wheel flange

AUD$16.00

Steering wheel flange, has outer bolt pattern of 6 x 5.5mm holes on 70mm PCD as well as inner three hole Go Kart bolt pattern. Can either be welded to steering column as per normal instalation or used as an adaptor plate from three hole to six hole when fitting a larger steering wheel.

PART NUMBER:SB05

Qty:

View Product Details

FRONT SHOCKS, (Pair) KIT

AUD$655.00

Front shocks, coilovers, gas filled, heavy duty, 14mm coils, rebuildable, adjustable preload, 390mm eye to eye. (2)

PART NUMBER:SHOCK 390

Qty:

View Product Details

Rear Shock (1) KIT

AUD$345.00

Rear Shock, gas filled heavy duty with 12mm coil springs, Adjustable spring preload, rebuildable, 465mm eye to eye

PART NUMBER:SHOCK465

Qty:

View Product Details

REAR SHOCKS, (Pair) KIT

AUD$765.00

Rear shocks, coilover, gas filled, heavy duty, 12mm coils, rebuildable, 750mm eye to eye. (2) Suits Piranha series II.

PART NUMBER:SHOCK 750R

Qty:

Shocks 790mm, (Pair) KIT

AUD$790.00

Shocks, coilover, gas filled heavy duty, 12mm coils, 790mm eye to eye, (2 shocks) suit front or rear of Barracuda, (2 pairs required for buggy).

PART NUMBER:SHOCK790

Qty:

View Product Details

Shock adjuster collar

AUD$38.00

Shock threaded adjuster collar, Aluminium, fits all Edge shocks, M60x2 thread, used for pre-loading spring.

PART NUMBER:SHOCKADJ

Qty:

View Product Details

Shock adjuster lock ring

AUD$36.00

Shock threaded adjuster lock collar, Aluminium, fits all Edge shocks, M60x2 thread, used for locking adjuster collar.

PART NUMBER:SHOCKLOK

Qty:

SLUG-10mm

AUD$5.00

Slug with 10mm drilled hole, 1", (25.4mm) OD. 40mm long. Used for motorcycle engine mounts that have 10mm mount holes.

PART NUMBER:SLUG-10mm

Qty:

SLUG-12mm

AUD$5.00

Slug with 12mm drilled hole, 1", (25.4mm) OD. 40mm long. Used for motorcycle engine mounts that have 12mm mount holes. Also used as shock mounts when making Sidewinder & Piranha front suspension arms, (4 required for front arm application) Not required if purchasing Edge SW07 front suspension arms.

PART NUMBER:SLUG-12mm

Qty:

SLUG-16mm

AUD$5.00

Slug with 16mm drilled hole, 1", (25.4mm) OD. 40mm long. Used for motorcycle engine mounts that have 16mm mount holes. Also used to make Raven, Fun Kart II & Trax II & Belcranks & lock collars, as well as the Raven brake bar. (Not required if buying these parts pre-fabricated from The Edge).

PART NUMBER:SLUG-16mm

Qty:

View Product Details

Stub Axles plain machined.

AUD$48.00

Machined pair of plain stub axles, comes with castle nuts, washers & split pins, (not required if ordering STUB032)

PART NUMBER:STUB-01

Qty:

View Product Details

Front Stub Axles (w/ Caliper mounts)

AUD$105.00

Front Stub axles, left & right, welded & drilled with uprights & steering arms, calliper mounts (2). Suit calipers CAL032x2 & wheel hubs FWH-04. Suits Sidewinder & Piranha.

PART NUMBER:STUB032

Qty:

View Product Details

Fuel Tap

AUD$18.01

Fuel tap, heavy duty ball valve, chrome plated brass with ¼” BSP female threads each end.

PART NUMBER:TAP-01

Qty:

View Product Details

Tie Down Straps

AUD$30.01

Motorcycle type Tie Down Straps. We use them for fixing down fuel tanks & for holding your vehicle on the trailer

PART NUMBER:TIEDOWN

Qty:

View Product Details

Rack and Pinion, KIT

AUD$415.00 (save $45.01)

13 days left!

Rack and Pinion. 1/2 turn lock, with adjustable gear mesh. Includes tie rods to suit Sidewinder and Piranha as well as input shaft adaptor

PART NUMBER:XRV RACK

Qty: